As you saw in the video, there's a ton that this kit can do. U0001 High speed CAN data bus. The electronic engine control unit (ECU) and devices connected to it are distinguished by their robust construction and are basically more reliable than connecting wires and connectors. P2269 State of water in the fuel. How to clear jcb fault codes on tires. The structure of the DTCs, also known as Diagnostic Trouble Codes (DTCs), has been standardized and represented by a 7-digit code for all road and off-road vehicles and vehicles. Let's kick off with a walkthrough of the software and then we will explain how to do a maintenance reset.
109 ALT The alternator is reporting a voltage even when the engine is not running. P0121 Range / Performance of "A" Sensor / Throttle / Pedal Position Switch. P250B Range / Performance Engine Oil Level Sensor Circuit. Jcb engine fault codes. P2125 Malfunction of channel 2 of a signal of a manual pedal. Flashloader tool will be updated with the details of the new software selected: Should an incorrect file be selected (with an incompatible make, machine type or power rating), the error below will be displayed (error changes on incompatibility e. g. make, machine type or power rating).
If there are clear signs of water contamination, the connectors must be allowed to dry completely before connecting. P2226 Chain "A" of the barometric pressure sensor. P0612 Control circuit of the engine speed relay. Vigate to the relevant machine software folder and select the relevant engine software based on the make, machine type and power rating above. 107 OIL SW The oil pressure switch is reporting oil pressure is present when the engine is not running. P2267 High fuel water sensor circuit signal. Disconnect the connectors and inspect their interior for contamination (usually water, oil, or hydraulic fluid). How to clear jcb fault codes on honda. The engineer also has the opportunity to erase the fault code log. 6th and 7th characters - are called "fault type bytes" (FTB) and indicate a specific fault (for example, 11 = short circuit to ground).
P0110 Intake Air Temperature Sensor 1 Circuit. Off the machine and wait for at least 2 minutes before performing any further operations on the machine. P0120 Throttle / Pedal Position Sensor / Switch A Circuit. JCB Diagnostic Trouble Codes. This error does not exist on machines fitted with an EEC. 250 RH IND The RH turn indicator is short-circuited. Engine is not running due to the fact that this is a proportional valve on these machines. The engine control unit automatically shuts off the engine to prevent an impending failure. Maintenance Reset Using Diesel Laptops Diagnostic Kit with TEXA Software.
P0274 High signal injector circuit 5th cylinder. P0106 Range / Performance of the manifold absolute pressure / barometric pressure circuit. Connect to the machine and select 'HYDRAULIC MANAGEMENT'. 163 STAB LH The stabilizer left (Rear Left / Rear Dozer on Auto's) solenoid is open-circuited. • exhaust white smoke. P0220 Circuit "B" of the sensor / switch throttle / pedal position.
P0617 Starter Relay Circuit High. P0566 Signal "off" ("Off") cruise control. • At low temperatures while idle: there may be an unstable idle, P0182 (flashing code 211) Malfunctioning fuel temperature sensor (low voltage faults shorted to ground). P0655 Malfunction of the engine test indicator light (CEL). • reduced output power. P0099 Intermittent / erratic intake air temperature sensor 2 circuit. U3FFF DTC SAE does not exist - specific manufacturer data required. Check the relevant machine documentation for the correct procedure. More Diagnostic Tools & Resources. P0183 High signal circuit "A" fuel temperature sensor. • Smoke output too large. P0117 (flashing code 23) engine coolant temperature sensor malfunction (low voltage error, ground fault, short circuit). 305 THRT CAL The error term of the PID algorithm is greater than 20 A/D points for more than 20 consecutive seconds. Go to the 'SETTINGS' tab and select 'SERVICE HOURS RESET'.
P0253 Low signal "A" of the fuel metering device of the high pressure fuel pump. P256A Idling Sensor / Switch Circuit. Please purchase the publication first if you want to download it. After connecting, all registered codes can be displayed. JCB Common Rail Fuel Codes. 238 HAMMER The hammer solenoid is short-circuited. 259 BRKE LT The brake light output is short-circuited. Reward Your Curiosity. P1501 Foot Choke / Pedal Failure - Low Torque. Selecting No will cancel the flash. The process will be very similar on any other machine as it is on the JCB Telehandler we will be doing the demo on today. 228 WASHER The washer motor is short-circuited. 241 TLBX LT The toolbox work light is short-circuited.
217 HORN The horn output is short-circuited. 215 BOOM PR The boom priority solenoid is short-circuited. P0192 (flashing code 245) fuel pressure sensor (low voltage or short circuit). Refer to Checking and Clearing Fault Codes. 301 ECW CAN The ECUW module is no longer communicating on the CAN bus.
101 CRANK A crank signal was not detected by the ECU1. U0121 Lost Communication With Anti-Lock Brake System (ABS) Control Module. 265 CRUISE The cruise control solenoid is short-circuited. 242 ENG SD The engine shutdown solenoid is short-circuited. 108 FLYWHEEL The flywheel sensor is reporting an engine speed even though the engine is not running. You are familiar with any safety cut out feature on the machine (seat switch) and do not invoke it during the flash i. e. do not interrupt the flash process. P1500 Faulty foot choke / pedal - emergency mode of movement to the place of repair work. P0374 No pulse "A" signal high-resolution time stamps. P0521 Range / Performance of the engine oil pressure sensor / switch. 220 HYD FAN The hydraulic fan solenoid is short-circuited. • Output power lowered. P0503 Intermittent / unstable / high signal "A" of the vehicle speed sensor. Broken connectors must be replaced.