Check the Bypass Switch. Then the softener flushes the salt brine out of the treatment medium and down the drain so the cleaned treatment medium will be ready to treat more water. ADVANCE CABINET SERIES WATER SOFTENER MANUAL. Water Softeners: During operation, the normal user displays are time of day or gallons remaining before regeneration will occur. For units that "Pre Fill" the brine tank, the valve will cycle back to the normal operating position.
Water conditioners do not remove nitrates or coliform bacteria, this requires specialized equipment. OVERFLOW LINE CONNECTION: An overflow drain line is recommended where a brine overflow could damage furnishings or the building structure. Teflon® tape must be used on the threads of the 1" NPT inlet and and outlet, the brine line connection at the control valve, and on the threads for the drain line connection. Using the wrong type of salt can cause bridges (crusty salt buildup) above the water level in the tank, preventing the water from being treated properly. During a normal regeneration this will be a 4 hour period for salt to dissolve. Kinetico dual-tank softeners still provide soft water while regenerating. ) If there is a demand for water when the system is regenerating, untreated water will be delivered. Is There Enough (Or Too Much) Water in the Tank? Note: The grains per gallon can be increased if soluble iron needs to be reduced. Pargreen Water Technologies Manuals. 5" GACS1035 32, 000 @ 15. Water softener service manual. 1* Refill port plug assembly 1 2 Elbow locking clip 1 3 Tube insert, 3/8 1 4 Nut, 3/8 1 5 Elbow cap, 3/8 1 6 O-ring 019 1 7 ** Refill flow control retainer assy.
Information in this manual is different than what is needed for installation and servicing of a particular water treatment system. Hyundai Portable Water Softener WS4000 Manual. Teflon® tape is not used on the nut connections or caps because "O" Ring seals are used. The user can scroll between the displays as desired. Water technologies water softener parts. Open the inlet handle of the bypass valve very slightly allowing water to fill the tank slowly in order to expel air. This takes about another 10 minutes.
The default is 20 with value ranges from 1 to 150 in 1 grain increments. When assembling the installation fitting package (inlet and outlet), connect the fitting to the plumbing system first and then attach the nut, split ring and "O" Ring. When the system begins to regenerate, the display will change to include information about the step of the regeneration process and the time remaining for that step to be completed. Unit regenerates C. time of regenerant set incorrectly at wrong time of day D. control set at "on 0" C. reset time of regeneration D. check with regeneration time option in programming E. control set at "NORMAL + on 0" E. check with regeneration time option in programming 5. Our detailed manuals and installation videos make most installations a breeze. During the first regeneration the unit will draw out the initial volume of brine/regenerant and refill it with the correct preset amount. Repeat steps 1 - 7 and now check the various cycles for proper operation. Do not locate unit where it or its connections (including the drain and overflow lines) will ever be subjected to room temperatures under 33° F. 3 5. Do not open the bypass at this time, it will be filled in the backwash position. Accessed by pressing set clock 2. Water technologies water softener manual pdf. Our US Water Systems are designed to be effective, user-friendly, and long-lasting.
EverGreen and AspenPro System Manuals. Install a 1/2" I. D. When Manually Regenerating a Water Softener, How Long for Each Cycle. flexible plastic tube to the Drain Line Assembly or discard the tubing nut and use the 3/4" NPT fitting for rigid pipe (recommended). This allows the service technician to draw brine and perform other tests without the test water going to the building. The bypass consists of two interchangeable plug valves that are operated independently by red arrow shaped handles. 1 on page 2) by opening the outlet bypass handle. Next and regen were pressed to reset the valve. These units will deliver conditioned water for many years to come, when installed and operated properly.
Programming: Installer Displays/Settings STEP 1 Press next and s simultaneously for 3 seconds.